How to Flash Infinix XPad 20 (X1102B) Stock Firmware (SP Flash Tool) — Fix Bootloop, Unbrick & FRP
This is a complete, device-specific guide to flashing Infinix XPad 20 stock firmware and using it to fix common software faults — a bootloop, a soft-brick, FRP lock, a corrupt system or a failed OTA. The Infinix XPad 20 runs on the MediaTek Helio G88 chipset, so it flashes with SP Flash Tool (SPFT) — the MediaTek flashing app for Windows. ROM Palace hosts 7 official stock firmware files for this model as a free, resume-supported direct download.
Before you start
- Back up anything you can — flashing erases the phone.
- Charge the battery above 50% so it cannot die mid-flash.
- Confirm your exact model code (X1102B) in Settings > About phone or on the box — flashing another model’s firmware can brick the device.
- Use a Windows PC and a good-quality USB data cable (not a charge-only cable).
💡 Flashing the wrong firmware, or pulling the cable during a flash, can hard-brick the phone. Only use the firmware listed for the Infinix XPad 20 on its ROM Palace page.
What you need
- The Infinix XPad 20 stock firmware — download it free from the Infinix XPad 20 firmware page on ROM Palace.
- SP Flash Tool (SPFT) — the MediaTek flashing app for Windows.
- the MediaTek USB VCOM / preloader driver installed on the PC so the tool can see the phone.
How to flash Infinix XPad 20 stock firmware
- Install the MediaTek USB VCOM (preloader) driver on your Windows PC, then open SP Flash Tool.
- In SP Flash Tool, click Scatter-loading and select the MTxxxx_Android_scatter.txt file from the extracted firmware.
- Leave the mode on Download Only (this keeps your IMEI safe) and click Download.
- Power the phone off completely and remove it from the cable.
- Connect the powered-off phone to the PC — the tool detects the preloader and the progress bar starts. On some models you hold Volume Down while plugging in.
- Wait until a green tick appears (Download OK). Do not unplug before that.
- Unplug and power on — the first boot after a flash can take a few minutes.
💡 The Infinix XPad 20 uses a MediaTek Helio G88 SoC — a "PMT changed" or "chip type not match" error means the scatter/firmware is for a different model — use only the file listed for this exact device.
Common problems and fixes
- Stuck in a bootloop after an update: flash the matching stock firmware from this page to restore a clean system.
- Tool never detects the phone: reinstall the MediaTek USB VCOM / preloader driver, try another USB 2.0 port, and connect with the phone fully off.
- FRP / Google account lock after a reset: flashing the full stock firmware clears the locked system partition.
- Battery drains fast or the phone won’t hold a charge after an update: reflash the stock firmware; if it persists, the 7000 mAh · 10W cell itself may be worn.
- Failed or interrupted OTA: a clean stock flash is the safe way back to a bootable system.
Infinix XPad 20 specifications
The specs below are what the Infinix XPad 20 firmware on this site targets:
| Spec | Detail |
|---|---|
| Chipset | MediaTek Helio G88 |
| Display | 11" IPS LCD · 90Hz |
| Battery | 7000 mAh · 10W |
| Camera | Main 8 MP; Front 5 MP |
| Software | Android 15 |
| Model code | X1102B |
⬇️ Need the software? Download official Infinix XPad 20 stock firmware free on ROM Palace — direct links, no waiting queue.
Frequently asked questions
What tool flashes the Infinix XPad 20?
The Infinix XPad 20 uses the MediaTek Helio G88 chipset, so it flashes with the MediaTek SP Flash Tool with the firmware’s scatter file on Windows. Load the firmware, arm the tool, then connect the powered-off phone.
Where can I download Infinix XPad 20 stock firmware for free?
ROM Palace hosts 7 official stock firmware files for the Infinix XPad 20 as a free, direct, resume-supported download — no queue, no quota, no sign-up. Open the model’s firmware page and pick the build for your region.
Will flashing fix a bootloop or FRP lock on the Infinix XPad 20?
Yes. Flashing the matching stock firmware rewrites the system and boot partitions, which clears a bootloop, a corrupt update or an FRP/Google lock left after a factory reset. Always use the firmware listed for your exact model code.