How to Flash itel A95 5G (A671N) Stock Firmware (SP Flash Tool) — Fix Bootloop, Unbrick & FRP
Flashing the factory firmware is the reliable way to revive a itel A95 5G that won’t boot, unbrick it, clear an FRP lock or roll back a bad update. Here is the full procedure for the itel A95 5G. The itel A95 5G runs on the MediaTek Dimensity 6300 chipset, so it flashes with SP Flash Tool (SPFT) — the MediaTek flashing app for Windows. ROM Palace hosts 2 official stock firmware files for this model as a free, resume-supported direct download.
Before you start
- Back up anything you can — flashing erases the phone.
- Charge the battery above 50% so it cannot die mid-flash.
- Confirm your exact model code (A671N) in Settings > About phone or on the box — flashing another model’s firmware can brick the device.
- Use a Windows PC and a good-quality USB data cable (not a charge-only cable).
💡 Flashing the wrong firmware, or pulling the cable during a flash, can hard-brick the phone. Only use the firmware listed for the itel A95 5G on its ROM Palace page.
What you need
- The itel A95 5G stock firmware — download it free from the itel A95 5G firmware page on ROM Palace.
- SP Flash Tool (SPFT) — the MediaTek flashing app for Windows.
- the MediaTek USB VCOM / preloader driver installed on the PC so the tool can see the phone.
How to flash itel A95 5G stock firmware
- Install the MediaTek USB VCOM (preloader) driver on your Windows PC, then open SP Flash Tool.
- In SP Flash Tool, click Scatter-loading and select the MTxxxx_Android_scatter.txt file from the extracted firmware.
- Leave the mode on Download Only (this keeps your IMEI safe) and click Download.
- Power the phone off completely and remove it from the cable.
- Connect the powered-off phone to the PC — the tool detects the preloader and the progress bar starts. On some models you hold Volume Down while plugging in.
- Wait until a green tick appears (Download OK). Do not unplug before that.
- Unplug and power on — the first boot after a flash can take a few minutes.
💡 The itel A95 5G uses a MediaTek Dimensity 6300 SoC — a "PMT changed" or "chip type not match" error means the scatter/firmware is for a different model — use only the file listed for this exact device.
Common problems and fixes
- Stuck in a bootloop after an update: flash the matching stock firmware from this page to restore a clean system.
- Tool never detects the phone: reinstall the MediaTek USB VCOM / preloader driver, try another USB 2.0 port, and connect with the phone fully off.
- FRP / Google account lock after a reset: flashing the full stock firmware clears the locked system partition.
- Battery drains fast or the phone won’t hold a charge after an update: reflash the stock firmware; if it persists, the 5000 mAh · 18W cell itself may be worn.
- Failed or interrupted OTA: a clean stock flash is the safe way back to a bootable system.
itel A95 5G specifications
The specs below are what the itel A95 5G firmware on this site targets:
| Spec | Detail |
|---|---|
| Chipset | MediaTek Dimensity 6300 |
| Display | 6.67" IPS LCD |
| Battery | 5000 mAh · 18W |
| Camera | Main 50 MP; Front 8 MP |
| Software | Android 14 |
| Model code | A671N |
⬇️ Need the software? Download official itel A95 5G stock firmware free on ROM Palace — direct links, no waiting queue.
Frequently asked questions
What tool flashes the itel A95 5G?
The itel A95 5G uses the MediaTek Dimensity 6300 chipset, so it flashes with the MediaTek SP Flash Tool with the firmware’s scatter file on Windows. Load the firmware, arm the tool, then connect the powered-off phone.
Where can I download itel A95 5G stock firmware for free?
ROM Palace hosts 2 official stock firmware files for the itel A95 5G as a free, direct, resume-supported download — no queue, no quota, no sign-up. Open the model’s firmware page and pick the build for your region.
Will flashing fix a bootloop or FRP lock on the itel A95 5G?
Yes. Flashing the matching stock firmware rewrites the system and boot partitions, which clears a bootloop, a corrupt update or an FRP/Google lock left after a factory reset. Always use the firmware listed for your exact model code.