How to Flash itel Ace 2 (ACE2P) Stock Firmware (SPD Upgrade Tool) — Fix Bootloop, Unbrick & FRP
This guide covers how to flash itel Ace 2 stock firmware end to end — the tool, the driver, the exact steps and the faults it fixes (bootloop, brick, FRP, corrupt system). The itel Ace 2 runs on the Spreadtrum chipset, so it flashes with the Unisoc SPD Upgrade Tool (ResearchDownload) — the Unisoc/Spreadtrum flashing app for Windows. ROM Palace hosts 2 official stock firmware files for this model as a free, resume-supported direct download.
Before you start
- Back up anything you can — flashing erases the phone.
- Charge the battery above 50% so it cannot die mid-flash.
- Confirm your exact model code (ACE2P) in Settings > About phone or on the box — flashing another model’s firmware can brick the device.
- Use a Windows PC and a good-quality USB data cable (not a charge-only cable).
💡 Flashing the wrong firmware, or pulling the cable during a flash, can hard-brick the phone. Only use the firmware listed for the itel Ace 2 on its ROM Palace page.
What you need
- The itel Ace 2 stock firmware — download it free from the itel Ace 2 firmware page on ROM Palace.
- the Unisoc SPD Upgrade Tool (ResearchDownload) — the Unisoc/Spreadtrum flashing app for Windows.
- the Unisoc / SPD USB driver installed on the PC so the tool can see the phone.
How to flash itel Ace 2 stock firmware
- Install the SPD/Unisoc USB driver on your PC, then open the SPD Upgrade Tool (ResearchDownload).
- Load the firmware: choose Load Packet / Load Firmware and select the .pac file you downloaded.
- Press Start Downloading so the tool is armed and waiting for the phone.
- Power the phone off completely.
- Hold the boot key (usually Volume Down, on some units Volume Up) and connect the USB cable while still holding it — the tool detects the phone and the bar starts.
- Wait for PASSED (green). Do not touch the cable until it finishes.
- Unplug and power on — the first boot after a flash can take several minutes.
💡 The itel Ace 2 uses a Spreadtrum SoC — a chip-type mismatch means you have the wrong .pac or the wrong tool — re-check that the firmware is the one listed for this exact model.
Common problems and fixes
- Stuck in a bootloop after an update: flash the matching stock firmware from this page to restore a clean system.
- Tool never detects the phone: reinstall the Unisoc / SPD USB driver, try another USB 2.0 port, and connect with the phone fully off.
- FRP / Google account lock after a reset: flashing the full stock firmware clears the locked system partition.
- Battery drains fast or the phone won’t hold a charge after an update: reflash the stock firmware; if it persists, the 1000 mAh cell itself may be worn.
- Failed or interrupted OTA: a clean stock flash is the safe way back to a bootable system.
itel Ace 2 specifications
The specs below are what the itel Ace 2 firmware on this site targets:
| Spec | Detail |
|---|---|
| Chipset | Spreadtrum |
| Display | 1.8" TFT |
| Battery | 1000 mAh |
| Model code | ACE2P |
⬇️ Need the software? Download official itel Ace 2 stock firmware free on ROM Palace — direct links, no waiting queue.
Frequently asked questions
What tool flashes the itel Ace 2?
The itel Ace 2 uses the Spreadtrum chipset, so it flashes with the Unisoc SPD Upgrade Tool with the .pac firmware on Windows. Load the firmware, arm the tool, then connect the powered-off phone.
Where can I download itel Ace 2 stock firmware for free?
ROM Palace hosts 2 official stock firmware files for the itel Ace 2 as a free, direct, resume-supported download — no queue, no quota, no sign-up. Open the model’s firmware page and pick the build for your region.
Will flashing fix a bootloop or FRP lock on the itel Ace 2?
Yes. Flashing the matching stock firmware rewrites the system and boot partitions, which clears a bootloop, a corrupt update or an FRP/Google lock left after a factory reset. Always use the firmware listed for your exact model code.