How to Flash itel Power 450 (P450) Stock Firmware (SPD Upgrade Tool) — Fix Bootloop, Unbrick & FRP
This guide covers how to flash itel Power 450 stock firmware end to end — the tool, the driver, the exact steps and the faults it fixes (bootloop, brick, FRP, corrupt system). The itel Power 450 runs on the Unisoc T107 chipset, so it flashes with the Unisoc SPD Upgrade Tool (ResearchDownload) — the Unisoc/Spreadtrum flashing app for Windows. ROM Palace hosts 5 official stock firmware files for this model as a free, resume-supported direct download.
Before you start
- Back up anything you can — flashing erases the phone.
- Charge the battery above 50% so it cannot die mid-flash.
- Confirm your exact model code (P450) in Settings > About phone or on the box — flashing another model’s firmware can brick the device.
- Use a Windows PC and a good-quality USB data cable (not a charge-only cable).
💡 Flashing the wrong firmware, or pulling the cable during a flash, can hard-brick the phone. Only use the firmware listed for the itel Power 450 on its ROM Palace page.
What you need
- The itel Power 450 stock firmware — download it free from the itel Power 450 firmware page on ROM Palace.
- the Unisoc SPD Upgrade Tool (ResearchDownload) — the Unisoc/Spreadtrum flashing app for Windows.
- the Unisoc / SPD USB driver installed on the PC so the tool can see the phone.
How to flash itel Power 450 stock firmware
- Install the SPD/Unisoc USB driver on your PC, then open the SPD Upgrade Tool (ResearchDownload).
- Load the firmware: choose Load Packet / Load Firmware and select the .pac file you downloaded.
- Press Start Downloading so the tool is armed and waiting for the phone.
- Power the phone off completely.
- Hold the boot key (usually Volume Down, on some units Volume Up) and connect the USB cable while still holding it — the tool detects the phone and the bar starts.
- Wait for PASSED (green). Do not touch the cable until it finishes.
- Unplug and power on — the first boot after a flash can take several minutes.
💡 The itel Power 450 uses a Unisoc T107 SoC — a chip-type mismatch means you have the wrong .pac or the wrong tool — re-check that the firmware is the one listed for this exact model.
Common problems and fixes
- Stuck in a bootloop after an update: flash the matching stock firmware from this page to restore a clean system.
- Tool never detects the phone: reinstall the Unisoc / SPD USB driver, try another USB 2.0 port, and connect with the phone fully off.
- FRP / Google account lock after a reset: flashing the full stock firmware clears the locked system partition.
- Battery drains fast or the phone won’t hold a charge after an update: reflash the stock firmware; if it persists, the 2500 mAh cell itself may be worn.
- Failed or interrupted OTA: a clean stock flash is the safe way back to a bootable system.
itel Power 450 specifications
The specs below are what the itel Power 450 firmware on this site targets:
| Spec | Detail |
|---|---|
| Chipset | Unisoc T107 |
| Display | 2.4" TFT |
| Battery | 2500 mAh |
| Camera | Main 0.3 MP |
| Model code | P450 |
⬇️ Need the software? Download official itel Power 450 stock firmware free on ROM Palace — direct links, no waiting queue.
Frequently asked questions
What tool flashes the itel Power 450?
The itel Power 450 uses the Unisoc T107 chipset, so it flashes with the Unisoc SPD Upgrade Tool with the .pac firmware on Windows. Load the firmware, arm the tool, then connect the powered-off phone.
Where can I download itel Power 450 stock firmware for free?
ROM Palace hosts 5 official stock firmware files for the itel Power 450 as a free, direct, resume-supported download — no queue, no quota, no sign-up. Open the model’s firmware page and pick the build for your region.
Will flashing fix a bootloop or FRP lock on the itel Power 450?
Yes. Flashing the matching stock firmware rewrites the system and boot partitions, which clears a bootloop, a corrupt update or an FRP/Google lock left after a factory reset. Always use the firmware listed for your exact model code.