How to Flash Villaon Hyper 100 (V6752L) Stock Firmware (SPD Upgrade Tool) — Fix Bootloop, Unbrick & FRP
If your Villaon Hyper 100 is stuck in a bootloop, soft-bricked, FRP-locked or refusing to boot after an update, reflashing the stock firmware is the clean fix. This guide walks the whole process for the Villaon Hyper 100. The Villaon Hyper 100 runs on the Unisoc T7250 chipset, so it flashes with the Unisoc SPD Upgrade Tool (ResearchDownload) — the Unisoc/Spreadtrum flashing app for Windows. ROM Palace hosts 2 official stock firmware files for this model as a free, resume-supported direct download.
Before you start
- Back up anything you can — flashing erases the phone.
- Charge the battery above 50% so it cannot die mid-flash.
- Confirm your exact model code (V6752L) in Settings > About phone or on the box — flashing another model’s firmware can brick the device.
- Use a Windows PC and a good-quality USB data cable (not a charge-only cable).
💡 Flashing the wrong firmware, or pulling the cable during a flash, can hard-brick the phone. Only use the firmware listed for the Villaon Hyper 100 on its ROM Palace page.
What you need
- The Villaon Hyper 100 stock firmware — download it free from the Villaon Hyper 100 firmware page on ROM Palace.
- the Unisoc SPD Upgrade Tool (ResearchDownload) — the Unisoc/Spreadtrum flashing app for Windows.
- the Unisoc / SPD USB driver installed on the PC so the tool can see the phone.
How to flash Villaon Hyper 100 stock firmware
- Install the SPD/Unisoc USB driver on your PC, then open the SPD Upgrade Tool (ResearchDownload).
- Load the firmware: choose Load Packet / Load Firmware and select the .pac file you downloaded.
- Press Start Downloading so the tool is armed and waiting for the phone.
- Power the phone off completely.
- Hold the boot key (usually Volume Down, on some units Volume Up) and connect the USB cable while still holding it — the tool detects the phone and the bar starts.
- Wait for PASSED (green). Do not touch the cable until it finishes.
- Unplug and power on — the first boot after a flash can take several minutes.
💡 The Villaon Hyper 100 uses a Unisoc T7250 SoC — a chip-type mismatch means you have the wrong .pac or the wrong tool — re-check that the firmware is the one listed for this exact model.
Common problems and fixes
- Stuck in a bootloop after an update: flash the matching stock firmware from this page to restore a clean system.
- Tool never detects the phone: reinstall the Unisoc / SPD USB driver, try another USB 2.0 port, and connect with the phone fully off.
- FRP / Google account lock after a reset: flashing the full stock firmware clears the locked system partition.
- Battery drains fast or the phone won’t hold a charge after an update: reflash the stock firmware; if it persists, the 5000 mAh · 18W cell itself may be worn.
- Failed or interrupted OTA: a clean stock flash is the safe way back to a bootable system.
Villaon Hyper 100 specifications
The specs below are what the Villaon Hyper 100 firmware on this site targets:
| Spec | Detail |
|---|---|
| Chipset | Unisoc T7250 |
| Display | 6.75" IPS LCD · 120Hz |
| Battery | 5000 mAh · 18W |
| Camera | Main 13 MP; Front 5 MP |
| Software | Android 15 |
| Model code | V6752L |
⬇️ Need the software? Download official Villaon Hyper 100 stock firmware free on ROM Palace — direct links, no waiting queue.
Frequently asked questions
What tool flashes the Villaon Hyper 100?
The Villaon Hyper 100 uses the Unisoc T7250 chipset, so it flashes with the Unisoc SPD Upgrade Tool with the .pac firmware on Windows. Load the firmware, arm the tool, then connect the powered-off phone.
Where can I download Villaon Hyper 100 stock firmware for free?
ROM Palace hosts 2 official stock firmware files for the Villaon Hyper 100 as a free, direct, resume-supported download — no queue, no quota, no sign-up. Open the model’s firmware page and pick the build for your region.
Will flashing fix a bootloop or FRP lock on the Villaon Hyper 100?
Yes. Flashing the matching stock firmware rewrites the system and boot partitions, which clears a bootloop, a corrupt update or an FRP/Google lock left after a factory reset. Always use the firmware listed for your exact model code.